The RV series of preassembled portable power systems are the perfect solution for adding house power to your RV, Motorhome, Caravan, camper trailer or work vehicle. Consisting of all you need for a complete portable power system, assembled onto a custom fabricated mounting panel with all necessary ancillaries, the RV series takes the guesswork out of assembling the components you need and the hardwork out of getting it all installed and playing nicely together.

With 18 variations on offer, you could be forgiven for wondering which one is for you. Selection is however straight-forward. If you would like to be able to rapidly recharge from a 240VAC source at a rate of 40A then narrow your search to the RV60 variants and ignore the RV80, whereas if you would like to double that charge rate then do the opposite. Next, if you are happy with basic ins and outs then an 01 variant suits. If you deem an 8-way fuse block to be a worthy inclusion then the 02 variants are for you. Alternatively, if you would like the added idiot-proofing offered by a low-battery cut-out, then the 03 variants are the ticket. Finally, you have a choice of 100Ah, 125Ah and 200Ah of Lithium battery storage, offering 1.2kWh, 1.5kWh or 2.4kWh of energy storage respectively.

Board dimensions: 480 x 400 x 100mm.

• Part Number: EN55050

This advanced battery monitor not only shows the true state of charge of your battery system. It also offers a large amount of additional features to optimally supervise your battery system and control external equipment. The ePRO Plus is compatible with lead based and Lithium batteries (LiFePO4).

• Complete battery status information at a glance on a single bank (%, V, A, Ah, W, h:m, C)
• Able to monitor up to 3 battery voltages (eg. House, Start & Generator bank)
• Full battery history information available
• Bluetooth dongle available as optional extra for free smartphone app connectivity

• Part Number: EN3DC40+

The Enerdrive ePOWER DC2DC+ Battery Charger is a fully automatic multistage, multi input battery charger with the ability to charge from either an alternator linked to a battery; or via solar power with the in built Maximum Power Point Tracking (MPPT) Solar Controller. With two inputs available, the main/house battery will be charged from either the engine while underway, or via the solar panels when stationary. The process to choose either engine or solar is fully automatic and both functions are controlled from within the unit itself without the need for external relays.

During normal operation the ePOWER DC2DC+ Battery Charger will do a full charge cycle to float stage on the house battery bank with ability to choose either GEL, AGM, Flooded, Custom Programmable or Lithium. Once float stage is reached the charger transitions to a power supply mode to support any on-board DC loads.

• Part Number: EN31220

The Enerdrive ePOWER 20A Battery Charger is a fully automatic, "set and forget" charger. It is designed to quickly and accurately recharge your batteries using algorithms that help maximise service life. Multistage smart charging technology enables the charger to be connected to your battery banks permanently.

• Multistage Charging: Fully automatic multistage battery charger with the ability to charge 3 separate battery banks.
• Separate Battery Banks: Isolated charging design where battery bank one is separate from battery bank two and three.
• Programmable: Battery bank 1 can be programmed with a different charge algorithm over banks 2 and 3.
• Current Control: User adjustable current output (e.g. Dial the 60amp unit back to run off a 1kVA generator).
• Smart Charging: The ePOWER 40A battery charger will regulate its output based on the loads connected to your battery banks.
   

• Part Number: EPL-125BT-12V

The Enerdrive B-TEC battery provides 60% more usable power than its equivalent lead acid cousin and being nearly 50% lighter and 30% smaller makes for a superior alternative.

The G2 now incorporates a 'Built-In Reset Button' making re-starting a flat battery a breeze. No longer do you need to apply a voltage to the battery terminals to wake up the battery. Press the button and within seconds, the battery will come back to life ready to accept a charge source to rejuvenate the battery.