Selleys Knead It Multipurpose is a versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded, stained and painted.

Features

• Will not sag, run or drip.
• Easy to use - no mess.
• Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing.
• Good adhesive strength.
• Can be used to reshape, rebuild and repair a multitude of surfaces and applications.
• Good gap filling properties.
• Long-lasting, durable solution.
• Heat resistant to 120°C continuously or 140°C intermittently.
• Can be used under water (but dry surfaces for application are best and recommended).
• Rapid set time (<10 minutes)
• Suitable for contact with drinking water. Complies with AS/NZS 4020
• Excellent anchoring properties

Where can this product be used?

• Repair and replacement - timber, metal, masonry, many plastics*, ceramics
• Mending - toys, appliances, lawn mowers, sports equipment etc
• Sealing - leaks in gutters and downpipes
• Patching - chipped concrete, floors, bricks, blocks etc
• Attaching - fixtures, machine tags, signs etc
• Anchoring - bolts, screws, housings etc
• Moulding - to reform-reshape damaged timber, metal, masonry, plastics, ceramics
• Moulding to rebuild - wrought iron fencing
• Forming knobs and missing parts
• Balancing - table legs etc
• Fixing a damaged roof tile
• Repairing a water (drinking) tank
• Lost the head off your hammer? Make a new one with Knead It.
• Replace chip in golf club (woods)
• Approval for Drinking Water Contact to AS/'NZ4020:2005, however limited to maximum surface area:volume ratio of 100 mm2/L atmaximum temperature of 85°C.

What materials is this product suitable for?

• Wood/Timber
• Concrete
• Anchoring bolts
• Metal
• Masonry
• Most plastics*
• Ceramics
• *Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon) or silicone rubber

How to use

1. Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning.
2. Cut off required amount. Replace disc on remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature.
3. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required.
4. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins.
5. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured.
6. After 5-10 minutes Knead It Multi Purpose will harden and begin to form a strong bond. After 60 minutes Knead It Multi Purpose may be drilled, sanded, machined, filed, sawed or painted.
7. Wash hands thoroughly with soap and water before product hardens.

Limitations:

• Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible
• *Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon) or silicone rubber 

Handy Tips

• Ensure the putty and hardener are mixed properly. Knead It will become warm as it is mixed. A good indication its mixed properly is when you have a uniform colour, and feel a mild heat radiating from the Knead It.
• To help determine when your knead it has set, keep a small piece off to check when it is hard, it indicates your job is done.
• Set time increases at temperatures below 20°C.
• Use Knead It Aqua for applications in wet/ submerged areas.
• Use Knead It Steel for applications on metal or fuel contact.

Clean up

• Remove excess and hand rub with water or a damp cloth
  before hardening begins.